MZ SKIN LightMAX MiniPro Eyeconic LED

Harnessing the power of LED technology to supercharge tour eye care routine, this first-to-market device delivers targeted light therapy to rejuvenate your eye area, targeting dark circles, puffiness, and fine lines and wrinkles to leave your eyes fresh, youthful, and awake looking.

Clinically proven to improve fine lines by up to 30% in four weeks, reduce wrinkle depth by 36% in four weeks, the red 630nm and near infrared 830nm wavelengths boos collagen production, calm inflammation, and minimise the visible signs of fatigue to rejuvenate tired and ageing eyes.

Reusable and ultra-thin, these rejuvenating LED eye patches adhere onto your skin with medical-grade hydrocolloid patches, the powerful active ingredients-enriched formulations working in conjunction with the LED therapy for combined efficacy.

Combatting fine lines, wrinkles, discolouration, and skin elasticity, the LightMAX MiniPro EYECONIC™ LED can also be used in any target areas like nasolabial folds, forehead, or areas that need localised repair to refresh and rejuvenate your skin.

The LightMAX MiniPro EYECONIC™ LED system consists of:

2 x Silicone LED Patches
2 x Magnetic 2 pin,
4mm to USB A Charging Cables
29 x Individually Wrapped Hydrocolloid Patches including 1 Sensitisation Patch 1 x User Manual 1 x Travel Pouch Technical Specifications: 630nm. NIR 830nm 6 diodes Power: 30mW/cm2 Energy: 18J/cm2 per 10min treatment. 

Benefits of MZ SKIN LightMAX MiniPro Eyeconic LED:

• Utilises LED technology to target ageing eyes.
• Supercharges your eyecare routine.
• Rejuvenates your eye area.

How to use:

For optimal results use 10 mins daily, 3-5 times per week. For all product information, visit the user manual. Remove the contents of the LightMAX MiniPro EYECONICTM LED box. Peel the device side of the Hydrocolloid Patch. Attach it to the LightMAX MiniPro EYECONICTM LED device.  Once secured to the device, peel the face side of the Hydrocolloid Patch. Press firmly onto your under-eye area until secure. Hold down the power button on each device until LED lights appear. After 10 minutes the LED device will automatically turn off signalling the end of your treatment. Remove gently from the skin. Remove the Hydrocolloid Patches from the LED and discard them. Using your ring finger, apply a small amount of Soothe & Smooth to the under eyes

Pro-tip: The LightMAX MiniPro EYECONIC™ LED can be used in any target areas like nasolabial folds, forehead, or even on the body in areas that need localised repair. Using LightMAX MiniPro EYECONICTM LED: Regarding electromagnetic compatibility (EMC) and electromagnetic fields (EMF), in and around the home environment the LightMAX MiniPro EYECONICTM LED should be kept away from radio frequency (RF) equipment to avoid interference. Treatment Recommendations: For the treatment of facial wrinkles, the best results are seen by treating for 3-5 times a week for 6 weeks.

Maintenance treatment should be carried out as required, according to lifestyle and skin condition.

Carrying out a treatment: DO NOT over flex the LightMAX MiniPro EYECONICTM LED device. Although it is flexible, it is not designed to withstand excess bending or folding. DO NOT use the LightMAX MiniPro EYECONICTM LED without a Hydrocolloid Patch. Ensure LightMAX MiniPro EYECONICTM LED is fully charged before commencing a treatment session. Cleanse or exfoliate the skin to remove any traces of skincare. Use a new Hydrocolloid Patch every treatment session. See the “How to use the Hydrocolloids” section for a step-to-step guide to using the Hydrocolloids.

Peel the device side of the backing paper off an adhesive Hydrocolloid Patch. Place the sticky side of the adhesive Hydrocolloid Patch onto LED side (white) of the LightMAX MiniPro EYECONICTM LED. Ensure the adhesive Hydrocolloid Patch aligns with the shape of the LightMAX MiniPro EYECONICTM LED. Press down across the entire surface of the adhesive Hydrocolloid Patch. Peel the face side of the backing paper from the adhesive strip. Using a mirror position the LightMAX MiniPro EYECONICTM LED over the treatment area. Switch ON the LightMAX MiniPro EYECONICTM LED. The device will automatically switch OFF after 10 minutes. You may stop the treatment at any time by pressing the ON/OFF button.

After the treatment, carefully remove the LightMAX MiniPro EYECONICTM LED and adhesive Hydrocolloid Patch from the treatment area. Remove the adhesive Hydrocolloid Patch from LightMAX MiniPro EYECONICTM LED and discard in general household waste. If you would like to keep the Hydrocolloid Patch on the treatment area after the LED treatment cycle has finished, press the Hydrocolloid Patch onto the face using the tab and carefully peel the LED device from the Hydrocolloid Patch.

Clean LightMAX MiniPro EYECONICTM LED by following the instructions in “Cleaning the LightMAX MiniPro EYECONICTM LED device”. Ensure that the device is NOT being charged when cleaning. You may treat more than one treatment area in a treatment session. DO NOT repeat a treatment on the same treatment area in the same session.

Care and Maintenance: The lifetime of the lithium battery can be maximised by allowing it to fully charge and then fully discharge during regular use.

Store LightMAX MiniPro EYECONICTM LED at room temperature in dry conditions. Avoid storing LightMAX MiniPro EYECONICTM LED in dusty conditions, in direct sunlight or in damp and humid conditions. LightMAX MiniPro EYECONICTM LED contains no serviceable parts.

Before each use, with the device switched off, clean the LightMAX MiniPro EYECONICTM LED following the cleaning instructions below. DO NOT use the LightMAX MiniPro EYECONICTM LED device any longer if it shows any signs of damage to the material through wear and tear. DO NOT use the Hydrocolloid after its expiry date. DO NOT use the LightMAX MiniPro EYECONICTM LED if it has been exposed to environmental conditions outside of those specified in the Technical Specification.

Cleaning the LightMAX MiniPro EYECONICTM LED Device: Before cleaning ensure that the charging cable is disconnected from the LightMAX MiniPro EYECONICTM LED and that the device is not charging. Clean the LightMAX MiniPro EYECONICTM LED with a water-based wipe. Stubborn stains or adhesive residue can be removed by wiping gently with 70% alcohol. DO NOT use water to clean LightMAX MiniPro EYECONICTM LED. DO NOT use the device if you think it has come into contact with water.

Size: 2 x LED patches